상품중이미지 썸네일
부가이미지 썸네일

SAE J2716 (SENT) to RS-232 Gateway

429,000 부가세포함

SAE J2716 (SENT) to CAN/RS-232 Gateway

수량
총 금액

SAE J2716 (SENT) to RS-232 Gateway

The SAE J2716 (SENT) to RS-232/CAN bus gateway features two bi-directional SENT (Single Edge Nibble Transmission) channels, two analogue output channels, and either RS-232 or CAN bus interface. The flexibility of the device allows the user to use it as a PC interface / SENT data logger, a gateway for PLC or a test system, and generally for SENT communication monitoring and simulation. The analogue outputs offer the possibility to directly convert SENT data frame signals into an analogue voltage.

 

Get the SENT-CAN and SENT-RS232 Data Sheet
User’s Manual
Communication Protocol Specification
Measurement of device delays

Features

  • SENT-to-CAN or SENT-to-RS-232 Gateway
  • SENT logger/tester/simulator
  • 2 SAE J2716 (SENT) channels
  • Each channel configurable as RX or TX, channels are independent
  • Supports Fast and Slow Messages according to SAE J2716:2016 (Fast, Short Serial, and Enhanced Serial)
  • Supports SENT/SPC
  • Configurable SENT channel parameters – Tick Time, Nibble Count
  • 2 analogue output channels (12-bit DAC, 0-4,095 V)
  • On-board remanent memory
  • Intelligent message filtration
  • 1x DSUB9F (RS-232/CAN), 1x 8-pin terminal block
  • Input power 9-30 V DC
  • 4x LED (3x Status, 1x Power)
  • 1x Reset switch
  • 5V DC output with over-current protection
  • Dimensions 108 x 54 x 30 mm
  • Table or DIN-rail mount
  • Hardware and firmware customization on request
  • Fast, Short Serial, and Enhanced Serial message formats are supported. The user can configure channel parameters (direction, tick time, nibble count, filtration) and store the configuration into the device’s non-volatile memory. Each SENT channel can be configured independently to suit all possible use cases: 2 RX channels / 1 RX and 1 TX channel / 2 TX channels.

    The converter offers two analogue output channels (12-bit DAC) that can be used to directly convert inbound SENT data frames into an analogue voltage. An analogue output channel can be mapped on any SENT channel. and the conversion parameters are fully configurable: StartBit, BitLength and a linear transfer function: Multiplier, Offset, Min/Max.

    An intelligent filtration of incoming SENT frames has been introduced so that RS-232 or CAN communication does not get overloaded. The CAN variant offers configurable CAN Identifiers for both TX and RX which allows multiple devices to be used simultaneously on the same CAN bus. The device’s firmware is upgradable from PC.

    A PC application “SENT Gateway Analyser” for configuring the device and for monitoring, logging and simulation of SENT communication is available for free. The device provides a communication protocol over RS-232/CAN so that the user can easily integrate the device into an existing system, such as test benches, HiL rigs and End-of-Line testers. The protocol provides function to configure the device’s SENT and analogue channels and to transmit and receive SENT Fast and Slow messages.

    Software and System Integration

    • Communication protocol for integration into existing systems
    • Free-of-charge “SENT Gateway Analyser” PC application for configuration, reception, transmission and logging
      note: The SENT Gateway Analyser application will work with any RS-232 port (COM port). For usage with SENT-CAN variant, the SENT Gateway Analyser uses Kvaser CAN driver for communicating over a CAN bus. Hence, a CAN interface by Kvaser is needed for communication with the SENT-CAN variant. The user can still control the device by raw CAN messages.
    • Analogue output channels to connect SAE J2716 bus to systems without SENT support
    • Device’s firmware upgradable from PC
































제조사 : Machsystem

 

 

번호 제목 답변여부 작성자 작성일
등록된 상품 문의가 없습니다.
반품/교환 안내

- 반품불가 표시된 상품 또는 해외 수입 제품은 제품의 불량 이외의 어떠한 사유로도 교환이나 반품이 되지 않습니다.

- 제품 특성상 고객님께서 제품을 충분히 확인하시고 주문하셔야 합니다. 쇼핑몰의 사진이나 설명은 단순 참고용 입니다.

- 해외 수입 제품이 아닌 경우 단순변심, 주문오류 등에 의한 반품 및 교환은 상품 수령일로 부터 7일 이내에 미개봉, 미사용, 미설치 된 제품에 한하여 교환이 가능합니다.

- 단순변심에 의한 반품 및 교환의 경우, 반품 및 교환을 위하여 추가로 발생되는 운임은 고객님 부담입니다.

- 배송박스가 훼손 되었거나, 제품이 파손된 경우 배송한 택배기사에게 즉시 알리고, 사진(파손부분, 송장부분)을 찍어 고객센터로 보내 주시기 바랍니다.

- 배달된 상품이 파손 되었거나, 기능상 불량, 하자가 있을 경우 상품수령일로 부터 7일 이내에 고객센터에 접수해 주시기 바랍니다.


배송 안내

- 결재금액이 5만원 미만은 배송비가 3,000원이며, 5만원 이상은 배송비가 무료입니다.

- 재고상품의 경우 주문 후 평균 2~3일내 (토요일, 공휴일 제외) 수령 가능하며, 택배사의 사정에 따라 다소 지연될 수 있습니다.

- 주문상품의 경우 평균 1~2주 기간이 소요 됩니다.

- 오후 3시 이후 입금 확인건은 다음날 주문 처리 됩니다.